Cement Lab Equipment

The complete set consists of one each:- 1.Glass plate 20 cm x 15 cm having ground ends and one side frosted. 2.Brass or stainless steel rod 3 mm dia x 150 mm long. 3.Flexible spatula. 4.Set of 6 moisture containers. 5.Porcelaine basin 150 mm dia. 6.Plastic wash bottle 500ml.

• Delivery Time: 2 Days

Composed of three grades (Grade I, Grade II and Grade III having the sizes 1 mm to 2 mm, 0.5 mm to 1 mm and 0.09 mm to 0.5 mm respectively), each one corresponding to 33.33% weight, was used as fine aggregate in the mortar.Price differs as the grade changes such as Grade l,ll,lll,lV,V. From Rs.1200-2450

• Delivery Time: 2 Days

Top Dia-100mm, Bottom Dia-200mm, Ht-300mm, Sheet Thickness-1.6mm min., As per IS: 7320, BS 1881.  It is used for the determination of the consistency of fresh mixed concrete where the maximum size of the aggregate does not exceed 38mm.

Core Cutter with Dolly (For Fine Graded Soil): 100mm Dia X130mm Long steel dolly Complete set with Rammer, Collar & Dolly etc.

We are leading trader, wholesaler and service provider of Survey Instrument, Cement Lab Equipment and Safety Equipment. The whole range is demanded for sturdy construction, less maintenance, optimum performance and longer functional life.

25/50 % With Chemical & All Accessories

• Delivery Time: 1 to 2 Days

Marshall Mould (150mm)

Centrifuge Extractor is used for determination and checking of Bitumen percentage in Bituminous mix, the mix is added with a solvent anddissolved bitumen is removed by centrifugal action. Consists of a removable Aluminum rotor bowl, Capacity 1500 gms. With a capand tightening nut.

25Kg

• Delivery Time: 2 Days

Range from 750/- to 850/-

 

Features:

• Longer service life

• Low maintenance

• Top performance

Range from 750/- to 1050/-

Range from 385/- to 550/-

Range from 21,000/- to 25800/-

Its is used for cleaning sieve to get better results.

Hot Air Oven: Internal Dimensions 18 x 18 x 18 Inch 45 x 45 x 45cm Temp. Range:50C above ambient to 2500C,+/- 10C, Temp. Control: Thermostat, Inner Chamber: MS,Outer Chamber: Mild Steel Powder Coated.

The aggregates should therefore have sufficient toughness to resist their disintegration due to impact. This characteristic is measured by impact value test. The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load.

Range from 425/- to 1650/- , Glassware Measuring Cylinder: Make - Borosil, Size -250ml, Single Metric Scale with Hexagonal Base, Class B

 As per IS specifications made in India 

It is used for measurement of resistance to plastic flow of cylindrical specimens of bituminous paving mixture loaded on the lateral surface. The machine can provide measurement data for use with hot mixture containing asphalt or tar and aggregate up to 25.4mm maximum size.

IS: 5515 IS: 1199, It consists of two conical hoppers & a cylinder mounter on a rigid metal frame. Complete with trowel and tamping bar-0-60 cms long x 16 mm dia. 

• Production Capacity: 4 to 5 Days

Capcity  3Ltr, 15 Ltr & 30 Ltr

(Blain Type)As per IS specifications Complete with brass permeability cell U tube manometer, rubber pipe and suction bulb with chemical.

IS: 1199, consists of vibrating table size-380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete set with all accessories.

Autoclave : for sterilization

 

Features:

• Longer working life

• Cutting edge technology

• Performance tested

Supplied with set of four springs, one each of approx 2Kg cm. 6Kg cm, and 8Kg cm. Complete as above in a wooden carrying case.

It is used with a suitable electronic balance for specific gravity determination of fresh and hardened concrete and aggregates.

Consists of mould 100mm dia x 127.3mm height x 1000ml volume with collar and Drainage base plate, Drainage cap, Metallic Clamping ring, two porous stone for base and cap, Dummy plate, set of three glass stand pipes approx. 6mm, 10mm and 20mm dia mounted on a wooden board, length of 3 meter rubber connection tube with pinch cock. 

U Bracket & swivel head. Penetration piston, 50mm dia threaded at the upper end. Supplied with following accessories - Dial Guage-0.01 mm x 25 mm travel & Proving Ring-Cap.5000 kg  

Range 850/- to 3550/-

For testing setting times Consists of a metallic frame bearing a movable rod with cap at one end and a vicat mould 70mm in dia at the base, 50mm at the top and 40mm high and with a glass base plate. 

150 mm x 150mm x 700mm Specimens.

Range from 450/- to 5,680/- & Available in different sizes

25 Kg

7 Kg (Non ISI), Range from 950/- to 1050/-

capacity 1000 kg (1 ton) cap. fitted with dial gauge 0.002mm/division with our calibration chart in a nice teak wooden case.